Sunkun Technology Service hotline
(+86)0755-28995058
(+86)0755-28995058
UV light curing how to reduce the printing the downtime
In the printing and packaging processing industry, equipment maintenance and printing machine downtime control to improve the profits of enterprises and increase the return on investment (ROI) is very important. This is mainly because most of the enterprise equipment in several shifts, in a few more hours of downtime when it isn't appropriate, can cause bigger loss. Is there a solution to reduce printing equipment downtime, the answer is yes, UV curing technology is one of the solutions.
Of course, improve the UV light curing, and it is a strange word. Because the UV light curing is a very reliable, and can replace the hot air dryer and other drying technology of curing technology, it is widely applied in printing and packaging processing industry has.
The advantages of UV light curing technology
UV curing technology began to embody one of the main advantages is the initial capital investment is less, the UV curing system compared with hot air drying equipment investment, UV curing systems in terms of investment in equipment can save 80% of their money. Other advantage of UV light curing is improves the production efficiency, improve the quality of printing quality and make the printing quality. In addition, the most prominent advantages of the UV curing light not in the printing workshop and the surrounding environment emissions VOCs (organic volatile).Maintain good UV system is the key to work out a preventive maintenance plan, and the maintenance of UV light curing system according to the plan. That means need to often check UV light curing system comprehensively, including work from top to bottom to overhaul. Check items including the UV lamp, lamp shade, and mirror gasket, and check the mercury relays, capacitors and other electronic components, etc.
The UV system maintenance
The UV light bulb is the core of any a UV system. Correct maintenance and handling of the UV lamp, not only can increase the service life of the UV lamp, but also can ensure the UV light bulb in the work under the condition of maximum luminous intensity. A UV light bulbs inspections every week, mostly looking for bad omen of the following:·End of the UV lamp
·Crimp end of UV lamp
·UV light bulb at the end of white
·Dust, attle deposited on quartz glass
·At the end of the UV lamp FaMo
If one appeared in the first three items, the UV system need for air conditioning or water regulation (UV curing system of cooling is not correct).
Don't outside, UV light bulb correctly is necessary. Should not take the UV lamp glass itself, but can only hold ceramic end, or wear a linen cloth gloves. On the skin grease can stick on quartz glass, after a while, in under the action of heat, grease will burn the UV lamp. Whenever you need to contact to the UV lamp, can be used after contact with an alcohol cleaning solvent scrubbing the UV lamp can remove the grease of the bulb.
The UV lamp shade itself also need a weekly cleaning and checking. Carefully check the UV light shielding device, in make sure air can flow into the UV light curing system at the same time to ensure that no excess UV light leakage. Air inlet filter should be kept clean, no dust and attle stay on its surface. If in the process used in UV light curing quartz plate, then you should to periodic washing of the quartz plate, to ensure the transmission properties of UV light are still valid.Matters needing attention
When you buy a set of UV light curing system, consider the following factors:
·Your factory maintenance personnel can easily cope with electronic components?
·Transformer compatible?
·Electric box can be cool, and there is plenty of filtered air it?
Before buying a UV light curing system considering the afore-mentioned problems, can save time and money.
The use of the above mentioned, the maintenance work steps of UV light curing system sounds a bit trouble, but they are indeed a good way to save time. Make every week one hour of time to do some preventive maintenance work, record the maintenance log, printing and postpress personnel will be able to make their UV light curing system is in the best working state, reducing equipment maintenance and downtime to a minimum. For troubleshooting, operation and maintenance of UV light curing system, UV light curing system manufacturers will provide a control platform, the platform can give users full computer control.
In the printing and post-press processing industry, printing machine downtime is inevitable. When the UV light curing for printing and post-press processing to improve production efficiency, improve the quality of printing products and realize the printing service diversification, preventive maintenance measures is a simple method avoid printing machine downtime at the inappropriate time. Before buying UV light curing system, remember system maintenance characteristics to qualify for UV light curing system, so that your company's printing machine down time will be reduced to a minimum.